K&L Supply

Seal Guide Assembly Tool 16x10mm K&L 35-8679 [TSSB16] Makes seal head installation quick and easy and, Very imporantly, the seal will not get damaged on sharp edges when sliding it onto the shaft. Part No. 00-109 (radhouse.co.uk)

Read more less

Seal Guide Assembly Tool 14x10mm K&L 35-8678 [TSSB14] Makes seal head installation quick and easy and, Very imporantly, the seal will not get damaged on sharp edges when sliding it onto the shaft. Part No. 00-108 (radhouse.co.uk)

Read more less

Seal Guide Assembling Tool. 12.5x10mm. [TSSB125] K&L 35-8677 Makes seal head installation quick and easy and, Very imporantly, the seal will not get damaged on sharp edges when sliding it onto the shaft. Part No. 00-107 (radhouse.co.uk)

Read more less

Clutch & Primary Gear PULLER Tool. K&L 35-8605 Removal tool for clutch & primary gears, flywheel and clutch bodies. This tool has 7 different holes for adjusting position. Set includes 5/8 puller bolt and 3x 6mm bolts. For use on 50cc KTM, LEM, COBRA, ACTION and Italjet 50cc Pee-Wee racing models. Part No. 00-098.KL (radhouse.co.uk) Cross reference numbers. 35-8605, MP51

Read more less

Flywheel Puller 30mm x 1.5-RH-External Female K&L 35-5938 Suzuki Suzuki DR200SE 2004 - 2009 Suzuki LT-F160 QuadRunner 1989 - 2001 Suzuki LT160E 1991 - 1992 Suzuki LT230E QuadRunner 1987 - 1993 Suzuki LT230GE 1985 - 1986 Suzuki LT230S QuadSport 1985 - 1988 Suzuki LT250EF 1985 - 1987 Suzuki LT250R QuadRacer 1985 - 1992 Suzuki LT250S 1989 - 1990 Suzuki TM125 1970 - 1975 Suzuki TM250 1970 - 1975 Suzuki TM400 1970 - 1975 Suzuki TS250 1970 - 2009 LT160/LT230/LT230G/LT250E/STM/MX Series 125/250/400 all years, TS250 Enduros. Also know to fit LT-F160N Quadrunner models. EARLY DR 4 STROKE MODELS. HARLEY 2-CYCLES 1969 Suzuki TS2501 Savage 1970 Suzuki TS2502 Savage 1971 Suzuki TM400R 1971 Suzuki TS250R Savage 1972 Suzuki TM250J 1972 Suzuki TM400J 1972 Suzuki TS250J Savage All pullers made to precise standards equal to factory original tools or better. Each tool and bolts are black oxide plated for rust protection. Tool hardness is softer than the motorcycle part to prevent damage to expensive crankshafts and flywheels. 5/8in. fine thread bolts used in all pullers. Tips on use. - Make sure the flywheel thread is clean of dirt and not damaged before screwing the puller in. - Use copper grease on the puller threads, for long life. - Make sure the puller is fully screwed into the flywheel. - After tightening use a hammer on the centre and tap to jolt free [not always need]. - If using old flywheel pullers make sure the threads are in good condition before use to avoid damage to flywheel. Part No. 00-095 (radhouse.co.uk) Cross Reference Numbers Only:MP8

Read more less

Internal Male MP21 Flywheel Puller 20mm x 1.5-RH-Internal Male. K&L 35-5945 Flywheel puller for 1976 Honda MR250 Elsinore, 1978-1979 Honda CB400A/T, CB450SC, CM450, CMX450C, CX500, CX650, GL500, GL650, MR250, NX250, PC800, 1981 Honda GL500I Silver Wing Interstate, 1981 Honda GL500 Silver Wing, 1982 HondaGL500I Silver Wing Interstate, 1982 Honda GL500D Silver Wing Deluxe UK Models, 1982 Honda GL500 Silver Wing, 1983 Honda VT750C Shadow, 1983 Honda GL650I Silverwing Interstate, 1983 Honda GL650 Silverwing, 1983 Honda GL500D Silver Wing Deluxe UK Models, 1984 Honda VT700C Shadow, 1984 Honda TRX250 Fourtrax, 1984 Honda GL650D2 Silverwing Deluxe UK Models, 1985 Honda VT700C Shadow, 1985 Honda VT1100C Shadow, 1985 Honda TRX250 Fourtrax, 1985 Honda GL650D2 Silverwing Deluxe UK Models, 00-094.MP CX650C 83, CX650TC 83, GL650 83, VF700C 87, VF750C 88, VT700C 84-87, VT750C 83, VFR800FI 98-00, VT800C 88, PC800 89-98, CBR900RR 00-03, VT1100C . Honda XR400 00-03, XR650R 00-05. ATC250ES 85-87, ATC250SX 85-87, ATC350X 85-86, TRX250 85-87, TRX300FW, TRX300EX 93-02, TRX350 86-87, TRX350D 86- 87, TRX400EX 99-02 All pullers made to precise standards equal to factory original tools or better. Each tool and bolts are black oxide plated for rust protection. Tool hardness is softer than the motorcycle part to prevent damage to expensive crankshafts and flywheels. 5/8in. fine thread bolts used in all pullers. Tips on use. - Make sure the flywheel thread is clean of dirt and not damaged before screwing the puller in. - Use copper grease on the puller threads, for long life. - Make sure the puller is fully screwed into the flywheel. - After tightening use a hammer on the centre and tap to jolt free [not always need]. - If using old flywheel pullers make sure the threads are in good condition before use to avoid damage to flywheel. Cross reference numbers ONLY. 07933-3950000, MP21, Part No. 00-094.KL (radhouse.co.uk). Honda ATC250ES 1985 - 1988 Honda ATC250SX 1985 - 2000 Honda ATC350X 1983 - 1989 Honda CB400A Hondamatic 1978 Honda CB400TI Hawk I 1978 - 1979 Honda CB400TII Hawk II 1978 - 1979 Honda CM400A Hondamatic 1979 Honda CM400T 1979 Honda CX500 1978 - 1979 Honda CX500C Custom 1979 Honda CX500D Deluxe 1979 Honda TRX250 1985 - 2011 Honda TRX250R 1987 - 1988 Honda TRX250X 1986 - 2011 Honda TRX300 FourTrax 1988 - 2000 Honda TRX300EX Sportrax 1986 - 2011 Honda TRX300FW FourTrax 4x4 1988 - 2000 Honda TRX350D 1987 - 1988 Honda TRX400EX Sportrax 1999 - 2002 Honda VF700C Magna 1987 Honda VF750C Magna 1988 Honda VT1100C Shadow 1987 - 2003 Honda VT1100C Shadow Spirit 1997 - 2007 Honda VT1100C2 Shadow ACE 1995 - 1999 Honda VT1100C2 Shadow Sabre 2000 - 2007 Honda VT1100C3 Shadow Aero 1998 - 2000 Honda VT1100T Shadow ACE Tour 1998 - 2000 Honda VT800C Shadow 1988 Honda XR250 1979 - 1980 Honda XR250L 1991 - 1996 Honda XR250R 1981 - 1994

Read more less

14mm x 1.50 Flywheel Puller STUD RH Male, Magneto K&L 00-0829 HONDA Honda ATC200 1981 - 1985 Honda ATC200E 1981 - 2004 Honda ATC200M 1984 - 1985 Honda ATC200S 1984 - 1986 Honda ATC200X 1981 - 2011 Honda CB125S 1973 - 1985 Honda TRX125 1985 - 1988 Honda TRX200 1984 Honda XL125 1970 - 1983 Honda XL125S 1979 - 1985 Honda XL185S 1979 - 1983 Honda XL200R 1983 - 1984 Honda XR185 1979 Honda XR200 1980 - 1984 Honda XR200R 1980 - 2003 All pullers made to precise standards equal to factory original tools or better. Each tool and bolts are black oxide plated for rust protection. Tool hardness is softer than the motorcycle part to prevent damage to expensive crankshafts and flywheels. 5/8in. fine thread bolts used in all pullers. Tips on use. - Make sure the flywheel thread is clean of dirt and not damaged before screwing the puller in. - Use copper grease on the puller threads, for long life. - Make sure the puller is fully screwed into the flywheel. - After tightening use a hammer on the centre and tap to jolt free [not always need]. - If using old flywheel pullers make sure the threads are in good condition before use to avoid damage to flywheel. Part No. 00-092 (radhouse.co.uk). Cross Reference Numbers Only:MP19

Read more less

20mm x 1.50 Flywheel extractor magneto Puller Hollow center. Fits MT 250 Series and MX2 cycle. MP7 Honda MT250 1974 - 1975 Yamaha RD250 1973 - 1975 Yamaha RD350 1973 - 1975 Yamaha YZ125 1974 - 1979 Yamaha YZ250 1974 - 1979 Yamaha YZ360 1974 - 1975 HONDA MOST EARLY MT SERIES EARLY MX 2 STROKE ENGINE MODELS YAMAHA MOST 1970s YZ125 MOST 1970s YZ250 MOST 1970s YZ360 Tips on use. - Make sure the flywheel thread is clean of dirt and not damaged before screwing the puller in. - Use copper grease on the puller threads, for long life. - Make sure the puller is fully screwed into the flywheel. - After tightening use a hammer on the centre and tap to jolt free [not always need]. - If using old flywheel pullers make sure the threads are in good condition before use to avoid damage to flywheel. Part No. 00-086 (radhouse.co.uk) Cross reference numbers ONLY. MX-12094, K&L 35-5937

Read more less

35mm x1.50 flywheel extractor puller with internal thread. K&L 35-5941 Rotax. Fits 600cc with large flywheel. 35mm x 1.5mm RH Female 4-stroke single cylinder models with large flywheels. Most 4 wheel ATV applications KAWASAKIKLT160, KLF185 Bayou, KLF220 Bayou, KLF250 Bayou and KLF300 Bayou. 1985-88 KLF185 Bayou 2003-10 KLF250 Bayou 1986-04 KLF300 Bayou 2x4 1989-04 KLF300 Bayou 4x4 ALL KSF250 Mojave MX SUZUKI 1990-99 DR350 1990-93 DR350S KAWASAKI 1985 KLT160 Tips on use. - Make sure the flywheel thread is clean of dirt and not damaged before screwing the puller in. - Use copper grease on the puller threads, for long life. - Make sure the puller is fully screwed into the flywheel. - After tightening use a hammer on the centre and tap to jolt free [not always need]. - If using old flywheel pullers make sure the threads are in good condition before use to avoid damage to flywheel. Part No 00-080 (radhouse.co.uk) Cross Reference Numbers Only:MP5

Read more less

Universal Puller. K&L 35-5953 Yamaha YFM 250 R Special 12 hole disc puller. Removes flywheel and electric starter magneto unit from the crankshaft. 6mm & 8mm bolts included. Universal applications: ATVs / Motorcycles Kawasaki, Yamaha, sea-doo and polaris. Tips on use. - Make sure the flywheel thread is clean of dirt and not damaged before screwing the puller in. - Use copper grease on the puller threads, for long life. - Make sure the puller is fully screwed into the flywheel. - After tightening use a hammer on the centre and tap to jolt free [not always need]. - If using old flywheel pullers make sure the threads are in good condition before use to avoid damage to flywheel. Part No. 00-079 (radhouse.co.uk)

Read more less

Float Level Gauge K&L. 35-9123 Measures float level height between the carburetor gasket surface and float. Fully adjustable to fit KEIHIN carburetors. Also effective for measuring other brands of carburetor and vapour seperators on marine EFI systems. Part No. 00-076.KL (radhouse.co.uk)

Read more less

Crankcase Separator Straight. K&L 35-9638. Sold as a set only. Part No. 00-056 (radhouse.co.uk)

Read more less

The Wheel Bearing Remover 8pcs Set (Kowa Seiki) K&L 35-9654 is a professional-grade tool designed for the safe and efficient removal of wheel bearings from motorcycle and ATV wheels. Manufactured in Japan, this set includes a range of metric split collar adapters to accommodate various bearing sizes, including those found on modern MX and European motorcycles. Features Designed to remove wheel bearings safely and easily from motorcycle and ATV wheels Includes new metric sizes compatible with recent MX and Euro motorcycles Dependable split collet design for secure engagement Professional quality construction Excellent quality; made in Japan Replacement pieces available separately Specifications Set includes 10mm, 12mm, 15mm, 17mm, 20mm, and 25mm split collar adapters Small split collar design Package quantity: 8 Cross-Reference OEM Part Numbers K&L 35-9654

Read more less

Part No. 00-052. (radhouse.co.uk)

Read more less

HD Piston Pin Keeper Drift Tool. K&L 35-5004 Able to install retaining ring at the piston area. Especially install round circle clip rings in one step. Short cone housing with notch and drift pin with notch. Application: H-Davidson BigTwin Cam 83-15, All sports late 85 & Buell 87-10 present (not 1125R models). Part No. 00-025.KL (radhouse.co.uk)

Read more less

Replacement Brushes (Pk of 3) The first brush specifically designed for cleaning motorcycle and bicycle drive chains. Rugged and oil resistant, this brush can be used on O-Ring and Non O-Ring chains. Brush blocks are easily adjusted to fit any size motorcycle or bicycle chains. Part No. 00-023 (radhouse.co.uk)

Read more less

INNER FORK DAMPER HOLDER K&L 35-0668 Size 10mm X 18mm taper square. For Kawasaki. Provides a positive means of holding the inner damper rod while removing the bolt from the bottom of the fork leg. 25-KAWASAKI Inner Damper Rod Holding Tool. Ideal tool to hold damper rod when disassembling and assembling front forks. It provides a secure method of holding the inner damper rod while removing the bolt from the bottom of the fork leg on Kawasaki models. Fit Kawasaki KDX/KX/KZ and Z series models. DRIVE 3/8" Inner Damper Rod Holding Tool K&L 35-0668 Part No. 00-017 (radhouse.co.uk)

Read more less

HD HARLEY Primary Cam Chain Tension Tool Fits all Harleys 99-06 FL, 99-05 FXD, 2000-2006 FXST. The tool designed with special clutch drive end for cam chain usage. Will unload the pressure on the primary and secondary chain tensioners to assemble and disassemble cams.Unloads pressure on the primary, secondarys chain tension while servicing H-D twincam models. Able to check springloaded tension. Hex.: 32MM x 1/2 Dr. O.D.:28 x H13MM. Includes two piece holding pin. OAL: 74MM x diameter: 2.3MM. Part No. 00-015.KL (radhouse.co.uk) Cross Reference Numbers Only:1283-1, 1283-2 Hold Pin, K&L 35-5002

Read more less

The EZE Brake Bleeder Pro Kit is a vacuum-operated syringe system designed to bleed master cylinders quickly and efficiently. Requiring only one person to operate, it simplifies the brake bleeding process without the need for special tools or clips. Developed by professional mechanics, the kit includes adaptors for common bleeder screw sizes and a sealed container for convenient storage. Features Vacuum-operated syringe bleeds master cylinder in seconds One-person operation—no special tools or clips required Designed for efficient and accurate brake bleeding Developed by mechanics for professional use Holds up to 40cc of brake fluid Includes sealed storage container Adaptors included for 1/4" and 3/8" brake bleeder screws Specifications Fluid Capacity: 40cc Compatibility: 1/4" and 3/8" bleeder screw systems Operation: Manual vacuum syringe Storage: Includes sealed container Cross-Reference OEM Part Numbers K&L 13-6515 Vehicle Fitments Fits all brake systems using 1/4" and 3/8" bleeder screws

Read more less

MV4530 Cooling System Pressure Test Kit. The Mityvac MV4530 Cooling System Pressure Test Kit quickly reveals external cooling system leaks, and detects internal leaks caused by a blown head gasket, or cracked block or head. The kit comes complete with a high-quality pressure pump and four (4) adapters for connecting to the cooling systems of most US and Asian manufactured cars and light trucks. For more adapter features, selection details, and vehicle make/model application guide, click on the link above. Cost saving adapter kits are featured below. Aplications: -Pressure testing for leaks in automotive cooling systems -Cooling system cap pressure testing (additional adapters required) Includes: -Hand Pressure Pump w/ 2 (610 mm) long hose and push-button pressure relief valve. -MVA100 Cooling System Adapter (US and foreign cars). -MVA101 Cooling System Adapter (Asian cars). -MVA102 Cooling System Adapter (Asian cars). -MVA103 Cooling System Adapter (US and foreign cars). -Cap Wrench. Part No. 00-0019.MV (radhouse.co.uk)

Read more less