TYGRIS

A non-abrasive stainless steel cleaner aerosol supplied in a 400ml can, formulated to remove grease, fingerprints and general grime from high-sheen surfaces. Suitable for stainless steel, chrome and aluminium, it leaves a protective film with a mild lemon fragrance and is safe on metals and coatings due to its silicone-free, acid- and alkali-free composition. Features Non-abrasive formulation to safeguard surfaces Deep grease and fingerprint removal Wide surface compatibility: stainless steel, chrome, aluminium; suitable for checkouts, window surrounds and kitchen exteriors Inert, silicone-free and acid/alkali-free; safe on metals and coatings Leaves a protective film with a light lemon fragrance Application guidance: shake vigorously; hold 15–30cm from surface; apply light spray; allow solvents to act; buff with a lint-free cloth; work section by section Safety guidance: use in well-ventilated areas; wear gloves; avoid inhaling spray mist; keep away from heat/sparks; read Safety Data Sheet before use Image for illustrative purposes only Specifications Volume: 400ml Appearance: Clear, colourless, thin liquid spray Odour: Mild, sweet lemon aroma Contents: Blend of cleaning solvents, technical white oil, hydrocarbon propellants Flash point: <0°C Relative density: 0.80 Temperature range: For use at ambient temperatures Flammability: Extremely flammable aerosol Hazards: May cause dizziness; pressurised container—do not expose to heat over 50°C Environmental note: Contains hydrocarbons; avoid release to water Packaging: 400ml aerosol cans, boxed

Read more less

A clear acrylic lacquer aerosol spray in a 400ml can, formulated as a fast-drying protective coating for electronics, metal, wood and paper documents. It forms a smooth, transparent, touch- and scratch-resistant film with good durability, offering resistance to mild acids, alkalis and general weathering, including sunlight, water and salt spray. Application is straightforward: shake well, spray upright from 25–30cm, allow 15–30 minutes to dry and 20 minutes between coats, then invert the can to clear the actuator. Always test previously coated surfaces for compatibility, consult the safety data sheet, wear suitable PPE, and dispose of used aerosols in line with local and national regulations. Features Fast drying Excellent resistance to weathering and sunlight High resistance to mild acids and alkalis Touch and scratch resistant finish Good resistance to water and salt spray Forms a smooth, transparent film with good durability and toughness Suitable for sealing and protecting electronics, metal, wood and paper documents Application guidance: shake well; spray upright from 25–30cm; allow 15–30 minutes to dry; 20 minutes between coats; invert can after use to clear actuator Safety guidance: consult safety data sheet; wear suitable PPE; test previously coated surfaces for compatibility; dispose of aerosols according to regulations Specifications Type: Acrylic lacquer Volume: 400ml Appearance: Clear slightly viscous liquid Odour: Solvent Contents: Blend of acrylic copolymer, adhesion promoter and ultraviolet absorber in acetone, 2-butoxyethanol, 2-methoxy-1-methyl-ethyl acetate in butane/propane propellant Flash point: -0°C Relative density: 0.885 Solubility: Insoluble in water Flammability: Extremely flammable Storage: Below 50°C

Read more less

TYGRIS Zinc Galvanizing Heavy Duty Spray Paint is formulated to deliver robust corrosion protection and serve as an effective primer for metal surfaces. It is especially suited for use on bare or previously galvanized metals and can be over-coated with various types of paint. The high-purity zinc content provides sacrificial protection, making it suitable for demanding environments exposed to oxidation and salt spray. Features High zinc content for maximum corrosion protection, including resistance to salt spray Zinc powder is of high purity (99.9%) Can be used on previously coated surfaces Suitable for over-coating with acrylic, alkyd, PU, and epoxy paints Specifications Volume: 400ml Appearance: Dark grey coating Odour: Characteristic paint aroma Contents: Acrylic and alkyd resins, micronised zinc, treated clay, solvents (xylene, acetone, 1-methoxy-2-propanol), butane/propane propellant Flash point: <0°C Solubility: Insoluble in water Temperature range: Dried film stable up to 70°C continuous Relative density: 1.150 Purity: Zinc powder 99.9% Laid down film: Zinc content 66%, film thickness 30–60 microns Salt spray test: 150 hours – successful Flammability: Extremely flammable Storage: Store below 50°C; shelf life 9 months Application: Shake well; spray from 25–30 cm; apply in light coats; allow 15–30 minutes drying before over-coating Disposal: In accordance with local and national regulations Cross-Reference OEM Part Numbers Not applicable Vehicle Fitments Not applicable

Read more less

TYGRIS Leak Detector Aerosol Spray 300 ml is an inoffensive, non-corrosive foam for inspecting pipework to quickly identify gas leaks that might otherwise pass unnoticed. Suitable for most materials and safe with most gases, it highlights leak points instantly by forming bubbles at the source. Consult the safety data sheet prior to use; wear appropriate PPE. Shake well before use, spray liberally onto the suspected area, and observe for a stream of bubbles indicating the exact leak location. Dispose of used aerosols in accordance with local and national regulations. Features Non-flammable water based Completely inert Detects the smallest leaks Will not form a combustible mixture with other gases Suitable for use with oxy-acetylene and LPG gases Non-corrosive Easily removed Specifications Appearance: Clear/white, slightly foaming liquid Odour: Virtually odourless Contents: Blend of ethanediol, ethoxylated alcohol and corrosion prevention additive in demineralised water with nitrogen propellant Flash point: <0°C Solubility: Soluble in water Temperature range: Designed for use at ambient temperatures Relative density: 1.02 pH: 7–7.5 Flammability: Extremely flammable Storage: Below 50°C Pack size: 12 × 300 ml aerosols

Read more less

An alcohol-based electrical cleaning aerosol supplied in a 400ml can, designed for use on electrical apparatus in electronics and switchgear. Suitable for cleaning and degreasing contacts, circuit boards and print heads, it evaporates cleanly leaving no residue. Safe with most plastics and on delicate instruments, with controlled drying to assist effective soil removal and low toxicity. Features Powerful and effective cleaner Removes stains, coatings, printing aids, oil, grease, dirt and most fluxes Leaves no residue Controlled drying time; evaporates quickly Safe with most plastics and on delicate instruments Does not cause corrosion of metals Low toxicity Application guidance: turn off electrical power; shake well; spray from 15–30cm; wipe off excess; avoid naked flames and hot surfaces; dispose of aerosols according to regulations Specifications Type: Alcohol-based electrical cleaner Volume: 400ml Appearance: Clear colourless liquid Odour: Strong alcoholic odour Contents: Blend of propan-2-ol with butane/propane propellant; no silicones or chlorinated solvents Flash point: <0°C Solubility: Slightly soluble in water Temperature range: Designed for use at ambient temperatures Relative density: 0.80 Flammability: Extremely flammable Storage: Below 50°C

Read more less

TYGRIS Bright Zinc Galvanizing Spray Paint is designed for the protective and cosmetic treatment of exposed metal areas on previously galvanized surfaces, particularly where welding or cutting has occurred. By utilizing zinc as a sacrificial metal, it offers effective rust and corrosion prevention while providing a bright finish that blends well with existing coatings. Features Zinc content assists in corrosion prevention Resistant to salt spray and weathering Excellent heat resistance Aluminium powder provides a brighter finish to match existing coatings Suitable for use on previously coated surfaces Contains high purity powders Excellent adhesion properties Quick drying formula Specifications Volume: 400ml Application distance: 25–30 cm Drying time: Approximately 10 minutes Finish: Bright zinc Usage: Shake well before use; apply in light coats; suitable PPE recommended Disposal: In accordance with local and national regulations Cross-Reference OEM Part Numbers Not applicable Vehicle Fitments Not applicable

Read more less

TYGRIS Weld Spatter Release WB 400 ml is a water-based, solvent-free formulation designed to prevent the adhesion of welding spatter on workpieces, nozzles, shrouds, jigs, and tools. Suitable for use on all types of welding equipment, it provides an environmentally considerate alternative to solvent-based products while delivering an effective non-stick surface. Features Prevents spatter adhesion Non-silicone – suitable for applications requiring subsequent finishing Excellent non-stick finish Non-flammable Water rinseable Dichloromethane free Consult the safety data sheet prior to use; suitable Personal Protection Equipment should be worn Shake can thoroughly before use and spray sparingly from a distance of 20 to 30 cm, ensuring even coverage Dispose of used aerosols in line with local and national regulations Image for illustrative purposes only Specifications Appearance: Pale yellow clear liquid Odour: Slight vegetable oil Contents: Blend of refined vegetable oils in a petroleum naphtha with butane, isobutane and propane propellant Flash point: <0°C Solubility: Insoluble in water Temperature range: Designed for use at ambient temperatures Relative density: 1.198 Flammability: Extremely flammable

Read more less

TYGRIS Cutting & Tapping Fluid Aerosol Spray is a high-performance lubricant designed for cutting, tapping, reaming, and turning operations. Formulated to extend tool life and enhance machining quality, it incorporates extreme pressure additives and corrosion inhibitors for effective performance on a wide range of metals, including stainless steel and titanium. Features Suitable for cutting, tapping, reaming, and turning Extreme pressure additives enhance performance on difficult materials High pressure foaming discharge improves penetration Prolongs tool life and improves machined finish Reduces heat buildup during operation Suitable for use on all metals Contains corrosion inhibitors Specifications Volume: 400ml Appearance: Brown, frothy liquid Viscosity: 300 cPs Odour: Sweet solvent odour Contents: Blend of naphthenic lubricants, petroleum wax, bitumens, polyisobutylenes, xylene, white spirit, viscosity improvers, extreme pressure additives, corrosion inhibitors, hydrocarbon propellants Chlorination: Non-chlorinated Flash point: <0°C Solubility: Insoluble in water Temperature range: For use at ambient temperatures Relative density: 0.840 Flammability: Extremely flammable Storage: Store below 50°C Application: Shake well; spray directly onto the tool area; avoid hot surfaces and open flames Disposal: In accordance with local and national regulations

Read more less

A high-performance, fast-evaporating brake and clutch cleaner supplied in an aerosol can for precise application. Formulated to remove oil, grease, brake fluid and dust rapidly, it dries without residue to restore clean, dry components. Suitable for industrial, automotive and engineering environments; non-chlorinated and effective on metal, ceramics and most plastics*. Features Rapid degreasing of oil, grease and brake dust No residue; fast-drying formula—no rinse required Helps reduce brake squeal and clutch slip by eliminating contamination Non-chlorinated; effective on metal, ceramics and most plastics* (*always test plastics prior to use) Multi-surface use: brake discs, callipers, drums, clutches and metal housings May affect some painted surfaces—test on an inconspicuous area first Not suitable for plastic or rubber components Not for use on live electrics or hot surfaces Application: shake well; spray directly at close range; allow excess to run off or evaporate; repeat if required Use only in well-ventilated areas and wear appropriate PPE Dispose of contaminated materials in a sealable container to avoid fire risk; dispose of used aerosols in line with regulations Image for illustrative purposes only Specifications Appearance: Colourless liquid Odour: Mild solvent Solubility: Insoluble in water Flash point: <0°C (propellant-driven) Evaporation rate: Rapid VOC content: 89.5% Shelf life: 24 months Volume: 400ml Packaging: Available in 600ml aerosol cans

Read more less

A black high-temperature aerosol spray paint supplied in a 400ml can for controlled application. Designed for demanding environments with quick-drying performance and a long-lasting glossy black finish, it is suitable for components such as engine blocks, brake drums and stoves. Supplied with two nozzle types (fan spray and direct spray) for application control, and formulated to cure to a heat-resistant silicone matrix that helps protect against heat, corrosion and wear. Surface preparation is straightforward and, when used correctly, a primer is not required. Touch dry in approximately 30 minutes when applied in light coats. Features Comes supplied with two nozzle types for superb painting control (fan spray and direct spray) Very high temperature paint (stated to handle up to 800°C) Quick drying Cures to a heat-resistant silicone matrix for protection against heat, corrosion and wear Long-lasting glossy black finish Touch dry in approximately 30 minutes with a few light coats Suitable for engine blocks, brake drums, stoves and similar applications Primer not required when used properly Image for illustrative purposes only Specifications Volume: 400ml Colour: Black (gloss) Appearance: Black coloured paint Odour: Characteristic paint odour Contents: A blend of naphtha and xylene with appropriate colouring pigments propelled by propane/isobutane Flash point: <0°C Solubility: Insoluble in water Temperature range: Working temperature up to 650°C Storage: Below 50°C

Read more less

A gloss dark green acrylic aerosol spray paint in RAL6005, supplied in a 400ml can for straightforward, controlled application. Formulated for high opacity and strong adhesion on stone, wood, metal and plastic, it offers excellent UV stability with added wear and scratch resistance. Two interchangeable nozzles (fan spray and direct spray) provide precise pattern control. A primer may be used for additional protection or where required. A full finish is typically achievable within 24 hours. Features High-quality acrylic formulation Excellent UV stability Scratch and wear resistant High-opacity for full coverage, including over previously painted surfaces Suitable for stone, wood, metal and plastic Two nozzles supplied: fan spray and direct spray for pattern control Primer recommended for added protection where required Typical finished result achievable within 24 hours Image for illustrative purposes only Specifications Colour: Gloss Dark Green (RAL6005) Volume: 400ml Appearance: Gloss Dark Green Odour: Typical paint odour Contents: Blend of pigments, viscosity modifiers, stabilisers, solvents and hydrocarbon propellants Flash point: <0°C Solubility: Insoluble in water Maximum temperature in use: 110°C Relative gravity: 0.797 VOC content: Approx. 91% Solids content: Approx. 9% Flammability: Extremely flammable Storage: Below 50°C

Read more less

A gloss KTM orange acrylic aerosol spray paint in RAL2004 (Pure Orange), supplied in a 400ml can for straightforward, controlled application. Designed as a high-quality finishing coat with fast-drying performance and full coverage, it adheres to a wide range of materials. Light surface sanding is recommended before use; a suitable primer may be applied for uneven surfaces, full colour changes, or added protection. Dry to the touch and ready for overcoating in approximately 15 minutes, with a typical finished result achievable within 24 hours. Please Note KTM’s exact orange can vary by model year and finish; Always confirm with a physical RAL fan deck or paint chip under project lighting.  Features High quality orange finishing paint Fast drying Suitable for a wide range of materials Full coverage with high opacity Acrylic formulation for improved flexibility and adhesion Two nozzles supplied: fan spray and direct spray for pattern control Light sanding recommended prior to application Primer recommended for uneven surfaces or full colour change/additional protection Dry to the touch and ready for overcoat in approximately 15 minutes Typical finished result achievable within 24 hours Image for illustrative purposes only Specifications Colour: Gloss KTM Orange (RAL2004 Pure Orange) Volume: 400ml Type: Acrylic Appearance: Gloss Orange Odour: Typical paint odour Contents: Blend of pigments, viscosity modifiers, stabilisers, solvents and hydrocarbon propellants Flash point: <0°C Solubility: Low water solubility Flammability: Extremely flammable Storage: Below 50°C

Read more less

Acrylic-based gloss yellow aerosol topcoat in RAL 1007, supplied in a 400 ml can for full-coverage finishing on a wide range of substrates including metals, plastics, and stone masonry. Provides high opacity with UV stability for durable colour retention, and wear and scratch resistance for added protection. Application control is provided by two interchangeable nozzles, with two mixing balls for rapid start-up. Fully dry in 24 hours. Image for illustrative purposes only. Features Acrylic-based top-coat paint High UV stability for extra durability High opacity for effective coverage Wear and scratch resistant Compatible with metals, plastics, and stone masonry Suitable for use over a prepared and primed surface if required Supplied with two nozzles: fan spray and direct spray Two mixing balls for fast start-up Quick adhesion and straightforward application Fully dry in approximately 24 hours Specifications Volume: 400 ml Colour/Code: Gloss Yellow, RAL 1007 Appearance: Yellow paint Odour: Typical paint odour (organic solvents) Composition: Blend of pigments, viscosity modifiers, stabilisers, solvents, and hydrocarbon propellants Drying time: Fully dry in approximately 24 hours Flash point: <0°C Storage: Below 50°C

Read more less

A gloss red acrylic aerosol spray paint in RAL3000, supplied in a 400ml can for convenient application. Designed as an acrylic-based topcoat with high opacity for full coverage, it provides wear and scratch resistance with high UV stability. Suitable for stone, plastic, and metals, it features two mixing balls for rapid agitation and is supplied with two interchangeable nozzles (direct spray and fan spray) for controlled application. Light surface sanding is recommended before use; a suitable priming spray may be used where full colour change or uneven surfaces are involved. Features Acrylic-based topcoat High opacity for full coverage Wear and scratch resistant High UV stability Suitable for stone, plastic, and metals Supplied with two nozzles: direct spray and fan spray Two mixing balls for fast start-up Light sanding recommended for surface preparation Compatible with use over suitable priming spray paints Image for illustrative purposes only Specifications Colour: Gloss Red (RAL3000) Volume: 400ml Appearance: Red paint Odour: Typical paint aroma (organic solvents) Contents: Blend of pigments, viscosity modifiers, stabilisers, solvents and hydrocarbon propellants Flash point: <0°C Storage: Below 50°C

Read more less

A gloss green acrylic aerosol spray paint in RAL6001, supplied in a 400ml can for controlled and convenient application. Designed as a high-quality finishing coat with quick-drying action, it is suitable for wood, stone and metal. Supplied with two interchangeable nozzles (fan spray and direct spray) for precise pattern control, and two mixing balls for rapid agitation. High opacity supports coverage over existing paint; a primer is recommended for uneven surfaces or full colour changes. Full results are typically achieved within 24 hours. Features Comes with a fan spray and direct spray nozzle High-quality gloss green finishing paint Quick-drying action Suitable for wood, stone and metal High opacity for coverage over existing paint Provides strong adhesion and flexibility Two mixing balls for faster start-up Primer recommended for uneven surfaces or full colour changes Specifications Colour: Gloss Green (RAL6001) Volume: 400ml Type: Acrylic Appearance: Green paint Odour: Typical paint aroma (organic solvents) Contents: Blend of pigments, viscosity modifiers, stabilisers, solvents and hydrocarbon propellants Flash point: <0°C Storage: Below 50°C

Read more less

Acrylic-based gloss blue aerosol spray paint in RAL 5010, supplied in a 400 ml can for premium finishing on a wide range of materials. Provides a wear-resistant topcoat with controllable application via two interchangeable nozzles and fast start-up from twin mixing balls. Adheres effectively to varied substrates and is suitable for use over primer for enhanced coverage. Fully dry in 24 hours. Image for illustrative purposes only. Features Premium quality finishing paint Wear resistant Supplied with two nozzles (fan spray and direct spray) Acrylic-based formula Adheres to a wide variety of surfaces Two mixing balls for fast start-up Quick-drying action Suitable as a topcoat over primer for added protection and coverage Gloss blue finish (RAL 5010) Specifications Volume: 400 ml Colour/Code: Gloss Blue, RAL 5010 Appearance: Blue paint Odour: Typical paint aroma (organic solvents) Composition: Blend of pigments, viscosity modifiers, stabilisers, solvents, and hydrocarbon propellants Nozzles supplied: Fan spray and direct spray Mixing balls: Two Drying time: Fully dry in approximately 24 hours Flash point: <0°C Storage: Below 50°C

Read more less

Acrylic-based grey self-etching primer aerosol designed as a dual-action etch/primer for preparing bare surfaces prior to topcoating. Provides strong adhesion on substrates including bare metal, aluminium, and fibreglass, with enhanced corrosion inhibitors and scratch resistance for additional protection. High opacity allows application over previously painted surfaces. Touch-dry and ready for overcoating in approximately 30 minutes. Supplied with two nozzles (fan and direct) for controlled application. Image for illustrative purposes only. Features Dual-action self-etching primer and primer in one Compatible with most types of materials Strong adhesion on bare metal, aluminium, and fibreglass Enhanced corrosion inhibitors help prevent rust Scratch resistant basecoat High opacity for effective coverage Can be applied over previously painted surfaces Ready for overcoating in approximately 30 minutes Supplied with two nozzles: one direct spray and one fan spray Specifications Type: Acrylic self-etching primer aerosol Volume: 400 ml Appearance: Light grey Odour: Typical paint aroma (organic solvents) Composition: Blend of pigments, viscosity modifiers, stabilisers, solvents, and hydrocarbon propellants Flash point: <0°C Storage: Below 50°C

Read more less

A black acrylic primer aerosol spray paint supplied in a 400ml can, designed to provide a high-adhesion, flexible basecoat on most surfaces. The formulation is wear and scratch resistant, offers corrosion protection on metal substrates, and delivers high opacity for efficient coverage over existing paint. Supplied with both fan spray and direct spray nozzles for controlled application, with fast-drying performance achieving a primer layer in approximately 15 minutes. Features Premium quality acrylic-based paint Works with most surfaces Wear and scratch resistant High adhesion and flexibility Corrosion protection against rust on metal surfaces High opacity for effective coverage over old paint with light coats Fast-drying; primer layer achievable in approximately 15 minutes Supplied with two nozzles: fan spray and direct spray Good controllability for consistent application Image for illustrative purposes only Specifications Colour: Black Volume: 400ml Type: Acrylic primer Appearance: Black Odour: Typical paint aroma (organic solvents) Contents: Blend of pigments, nitro-cellulose binder, solvents and hydrocarbon propellants Flash point: <0°C VOC content: Approx. 85% Solids content: Approx. 15% Maximum temperature in use: 110°C Storage: Below 50°C

Read more less

A bright silver aerosol spray paint in RAL9006, supplied in a 400ml can for convenient application. Formulated for long-lasting durability and fast drying, it is suitable for wood, metal and a variety of other substrates. High opacity supports coverage of previously painted surfaces with light coats, and two nozzles provide control over spray pattern. Light surface sanding is recommended before use; a primer may be applied on uneven surfaces, for full colour changes, or added protection. Features Long-lasting and durable Designed for a variety of surfaces, including wood and metal Fast-drying High opacity for coverage of previously painted surfaces with light coats Acrylic formulation Two nozzles for controlled spray pattern Suitable for automotive applications Provides flexibility Anti-wear protection Light sanding recommended for surface preparation Primer coat recommended for uneven surfaces, full colour changes or additional protection Specifications Colour: Bright Silver (RAL9006) Volume: 400ml Appearance: Bright Silver Odour: Typical paint aroma (organic solvents) Contents: Blend of pigments, nitro-cellulose binder, solvents and hydrocarbon propellants Flash point: <0°C Storage: Below 50°C

Read more less

Acrylic-based gloss white aerosol topcoat in RAL 9010, suitable for professional finishes on most substrates with high opacity and excellent adhesion. Supplied in a 400 ml can with two interchangeable nozzles (direct and fan) for controlled application. Touch-dry and ready for overcoating in 15 minutes and fully dry in 24 hours. Image for illustrative purposes only. Features Acrylic formulation for greater flexibility Gives excellent adhesion Compatible with most materials Can be applied over previously painted surfaces Wear and scratch resistant High opacity Supplied with two nozzles: direct spray and fan spray Consult the safety data sheet prior to use; suitable personal protective equipment should be worn Surface should be clean, dry, and grease-free; apply primer first for uneven surfaces, complete colour changes, or extra protection Prepare with a light sanding for good adhesion Shake can vigorously for 2 minutes Adjust nozzle for desired spray pattern; apply a number of light coats with a sweeping action from 25–30 cm Paint is touch-dry and ready for overcoating in approximately 15 minutes; fully dry within 24 hours After use, invert can and spray to clear nozzle Coverage: approximately 1.5–2 m² per can Dispose of used aerosols in line with local and national regulations Specifications Type: Acrylic topcoat aerosol Volume: 400 ml Colour/Code: Gloss White, RAL 9010 Appearance: Gloss white Odour: Typical paint aroma (organic solvents) Composition: Blend of pigments, nitro-cellulose binder, solvents, and hydrocarbon propellants Flash point: <0°C VOC content: Approx. 91% Solids content: Approx. 9% Maximum temperature in use: 110°C Storage: Below 50°C

Read more less

Acrylic red primer aerosol spray paint in a 400 ml can, designed to provide strong adhesion, high opacity, and flexible priming performance on most substrates. Suitable for application over previously painted surfaces, with wear- and scratch-resistant properties and corrosion protection for metal. Supplied with direct spray and fan spray nozzles for controlled application and two mixing balls for rapid start-up. Fast-drying; typically touch-dry in 15 minutes. Image for illustrative purposes only. Features Acrylic formulation provides flexibility Strong adhesion High opacity for effective coverage Compatible with most substrates Can be applied over existing painted surfaces Wear and scratch resistant Protects against rust and corrosion Includes direct spray and fan spray nozzles for control Two mixing balls for quick start-up Fast-drying; typically touch-dry in approximately 15 minutes Effective results achievable with light sanding and a few coats Lead free Specifications Volume: 400 ml Appearance: Red Odour: Typical paint aroma (organic solvents) Composition: Blend of pigments, nitro-cellulose binder, solvents, and hydrocarbon propellants Flash point: <0°C Storage: Below 50°C

Read more less

Acrylic-based white primer aerosol spray paint in a 400 ml can, designed to provide a high-opacity base coat on a wide range of substrates including metal, aluminium, and fibreglass. Adheres well to previously painted surfaces, sands easily, and is wear and scratch resistant. Supplied with two easy-to-fit nozzles (fan and direct) for controlled application. Touch-dry and ready for overcoating in approximately 15 minutes. Image for illustrative purposes only. Features Premium quality, high-opacity primer Acrylic-based formula Compatible with most materials, including metal, aluminium, and fibreglass Strong adhesion; can be applied over previously painted surfaces Wear and scratch resistant Easy to sand; effective results with light sanding and a few light coats Ready for overcoating in approximately 15 minutes Supplied with two nozzles: fan spray and direct spray Specifications Volume: 400 ml Appearance: White Odour: Typical paint aroma (organic solvents) Composition: Blend of pigments, nitro-cellulose binder, solvents, and hydrocarbon propellants Flash point: <0°C VOC content: Approx. 85% Solids content: Approx. 15% Maximum temperature in use: 110°C Storage: Below 50°C

Read more less

Acrylic grey primer aerosol spray paint in a 400 ml can, designed for fast, reliable adhesion on most materials and suitable for application over previously painted surfaces. Offers high opacity, corrosion protection, and a wear- and scratch-resistant base coat that sands easily and is ready for overcoating. Supplied with two simple-to-fit nozzles for controlled application and two mixing balls for rapid start-up. Image for illustrative purposes only. Features Fast-drying priming spray Compatible with most materials Supplied with two simple-to-fit nozzles Can be applied over existing painted surfaces High opacity for effective coverage Easy to sand with wet and dry paper Wear and scratch resistant Provides corrosion protection for metal surfaces Ready for overcoating Effective results achievable with a few light coats Two mixing balls for quick start-up Specifications Type: Acrylic primer aerosol Volume: 400 ml Appearance: Grey Odour: Typical paint aroma (organic solvents) Composition: Blend of pigments, nitro-cellulose binder, solvents, and hydrocarbon propellants Lead content: Lead free Drying time: Approximately 15 minutes to touch Flash point: <0°C VOC content: Approx. 85% Solids content: Approx. 15% Maximum temperature in use: 110°C Storage: Below 50°C

Read more less

Acrylic-based gloss black aerosol spray paint in RAL 9005, designed for high-opacity coverage on most substrates and suitable for application over previously painted surfaces. Provides a durable, wear- and scratch-resistant finish with high UV stability to help resist fading. Supplied with two interchangeable nozzles (fan and direct) and two mixing balls for efficient preparation and controlled application. Features Acrylic-based formula with high opacity Can be applied over previously painted surfaces Wear and scratch resistant High UV stability for a non-fading gloss finish Suitable for most substrates Supplied with two nozzles: fan spray and direct spray Includes two mixing balls for rapid start-up Dry to the touch in approximately 15 minutes; fully dry in 24 hours Effective coverage achievable with a few light coats Compatible with acrylic primers Specifications Colour/Code: Gloss Black, RAL 9005 Volume: 400 ml Appearance: Black paint Odour: Typical paint aroma (organic solvents) Composition: Blend of pigments, nitro-cellulose binder, solvents, and hydrocarbon propellants Lead content: Lead free Flash point: <0°C Storage: Below 50°C

Read more less