Nitrogen Shock Guage And Filler 300PSI Motion Pro 08-0072

Description

The Motion Pro Nitrogen Shock Gauge and Filler is engineered for precise filling of gas-charged shocks. With a capacity of up to 300 psi, it features a bleeder valve and a T-handle plunger pin chuck for accurate pressure adjustments. The swivel chuck is equipped with a 12-inch flexible hose to facilitate easy access. The kit includes instructions, a carrying box, and a Schrader valve extension, which is necessary for certain Showa shocks. Please note, a regulator and transfer hose are required to connect nitrogen from the tank to the shock gauge and filler. This tool is proudly made in the USA.

Features:

  • 300 psi capacity
  • Bleeder valve for precise pressure control
  • T-handle plunger pin chuck
  • Swivel chuck with 12-inch flexible hose
  • Includes Schrader valve extension for specific Showa shocks
  • Made in the USA

Specifications:

  • Pressure Capacity: Up to 300 psi

WARNING! FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN GREAT BODILY HARM AND/OR DEATH! IT IS IMPERATIVE THAT YOU REGULATE THE NITROGEN PRESSURE FROM THE TANK DOWN TO A SAFE PRESSURE UNDER 300 PSI! NEVER APPLY FULL TANK PRESSURE TO THIS TOOL! Wear eye protection to prevent eye injury from escaping gas and/or metal chips. We recommend that a qualified mechanic in a properly equipped shop perform this procedure.

CAUTION! Always follow shock manufacturers' instructions and only fill to their recommended pressure.

  • Support the motorcycle securely on a stand with the rear wheel off the ground.
  • Remove the Schrader valve cap from the shock. Bleed off any nitrogen pressure remaining in the shock reservoir.
  • Lightly turn T-handle valve counter-clockwise to stop. Next, connect T-handle valve to Schrader valve on shock. Tighten T-handle valve very lightly with an 11/16" wrench to ensure a good seal.
  • Turn T-handle valve clockwise while nitrogen pressure from the tank is being applied to Motion Pro gauge. A slight deflection of the Motion Pro gauge needle will occur when the T-handle valve has opened the shock Schrader valve.
  • Wait a few seconds, and then lightly turn the T-handle valve counter-clockwise to stop. Remove nitrogen tank hose from Motion Pro gauge. Bleed pressure from Motion Pro gauge by depressing the bleeder valve button. Motion Pro gauge may safely be removed from shock now. Replace Schrader valve cap on shock.

NOTE:

  • On some Showa shocks, the Schrader valve extension (08-0132) is required. This extension is included with the Motion Pro Shock Gauge #08-0072.
  • On some Yamaha and Ohlins shocks, there is a self-sealing rubber valve. The Motion Pro Nitrogen Needle (08-0075) is required to pressurize these shocks. The nitrogen needle is sold separately.

Nitrogen Shock Guage And Filler 300PSI Motion Pro 08-0072

Product form

The Motion Pro Nitrogen Shock Gauge and Filler is engineered for precise filling of gas-charged shocks. With a capacity of... Read more

Out of stock

£219.90 Incl. VAT

    • Guaranteed secure & safe checkout.

      shop pay

    SKU: 00-072

    • Free shipping on all orders above £75
    • No hassle returns within 30 days

    Description

    The Motion Pro Nitrogen Shock Gauge and Filler is engineered for precise filling of gas-charged shocks. With a capacity of up to 300 psi, it features a bleeder valve and a T-handle plunger pin chuck for accurate pressure adjustments. The swivel chuck is equipped with a 12-inch flexible hose to facilitate easy access. The kit includes instructions, a carrying box, and a Schrader valve extension, which is necessary for certain Showa shocks. Please note, a regulator and transfer hose are required to connect nitrogen from the tank to the shock gauge and filler. This tool is proudly made in the USA.

    Features:

    • 300 psi capacity
    • Bleeder valve for precise pressure control
    • T-handle plunger pin chuck
    • Swivel chuck with 12-inch flexible hose
    • Includes Schrader valve extension for specific Showa shocks
    • Made in the USA

    Specifications:

    • Pressure Capacity: Up to 300 psi

    WARNING! FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN GREAT BODILY HARM AND/OR DEATH! IT IS IMPERATIVE THAT YOU REGULATE THE NITROGEN PRESSURE FROM THE TANK DOWN TO A SAFE PRESSURE UNDER 300 PSI! NEVER APPLY FULL TANK PRESSURE TO THIS TOOL! Wear eye protection to prevent eye injury from escaping gas and/or metal chips. We recommend that a qualified mechanic in a properly equipped shop perform this procedure.

    CAUTION! Always follow shock manufacturers' instructions and only fill to their recommended pressure.

    • Support the motorcycle securely on a stand with the rear wheel off the ground.
    • Remove the Schrader valve cap from the shock. Bleed off any nitrogen pressure remaining in the shock reservoir.
    • Lightly turn T-handle valve counter-clockwise to stop. Next, connect T-handle valve to Schrader valve on shock. Tighten T-handle valve very lightly with an 11/16" wrench to ensure a good seal.
    • Turn T-handle valve clockwise while nitrogen pressure from the tank is being applied to Motion Pro gauge. A slight deflection of the Motion Pro gauge needle will occur when the T-handle valve has opened the shock Schrader valve.
    • Wait a few seconds, and then lightly turn the T-handle valve counter-clockwise to stop. Remove nitrogen tank hose from Motion Pro gauge. Bleed pressure from Motion Pro gauge by depressing the bleeder valve button. Motion Pro gauge may safely be removed from shock now. Replace Schrader valve cap on shock.

    NOTE:

    • On some Showa shocks, the Schrader valve extension (08-0132) is required. This extension is included with the Motion Pro Shock Gauge #08-0072.
    • On some Yamaha and Ohlins shocks, there is a self-sealing rubber valve. The Motion Pro Nitrogen Needle (08-0075) is required to pressurize these shocks. The nitrogen needle is sold separately.

    Shipping & Delivery

    How long will my item take to arrive?

    Orders are typically dispatched within 1 working day and are shipped on a 24hour (non-guaranteed) service.

    Where do you ship to?

    We currently only ship orders within the UK.

    How can I track my order?

    Once your order has been dispatched, you will receive a tracking code. Tracking information is emailed to the email address that was provided when placing the order.

    Can I collect my order?

    Unfortunately we do not offer order collections from our fulfilment centre.

    WHY NOT CHECK OUT

    Recently viewed products

      Sign up for our newsletter

      Subscribe to our Mailing List

      Never miss any news and be the first to know about sale and offers

      © 2026 Radhouse, Powered by Shopify

        • American Express
        • Apple Pay
        • Diners Club
        • Discover
        • Google Pay
        • Maestro
        • Mastercard
        • PayPal
        • Shop Pay
        • Union Pay
        • Visa